writer & blogger

  • How to solder high pressure ball valves

             How to solder high pressure ball valves

    High pressure ball valves are generally used in plumbing. They are installed in the cold and war water copper lines so if you have do a repair work like changing the faucets on a sink or taking out a sink to put a fresh one in, you do not have to turn off the water to the full home. You just turn off the ball control device on the water lines leading to the job project. The handle of the valve is linked to an internal ball that has hole running via it. When the valve is the unlock place the hole in the ball is lined up with the opening in the copper pies on either side of it. When the high pressure ball valve is the closed place the holes disappear from in front of pipe openings no water can run through. Soldering in a high pressure ball valve is not different from soldering a normal copper united. Here is tutorial on solder in a high pressure ball valve on a fresh copper water pipe installation,

    Step 1

    Dry fit the piping and copper on either ball valve side. Put the pipe copper out and dirt-free it.

    Apply Emory paper to smooth the exterior of the copper pipe until it is shiny and bright looking. Force a wire-fitting brush into both finish of the high pressure ball valve and twist it around to clean the within of the copper tubing of the control device.

    Step 2

    Brush paste flux on the exterior of the copper pipe and the within of both ends of the high pressure ball valve.

    Step 3

    Force the  pipe copper ends into the high pressure ball valve. Before beginning to solder ensure the ball control device is in the open place.

    This means the grip of the high pressure ball valve is parallel to the copper pipe.

    Step 4

    Light the propane torch. Grip a spool of wire solder in the non-leading hand.

    Begin warming up the copper pipe where it enters the high pressure ball valve one just one side. Watch the flux.

    When it turns gooey and brown in look and begins to bubble the metal is getting warm enough for the solder to flow. Touch the tip of the wire solder to the steam and watch for it to melt and flow fully around the seam.


    When the high pressure ball valve and copper pipe have cooled fully, take a paper towel and cover it in the region of the pipe where it meets the control device and rub dynamically to dirt-free the surplus flux off the pipe. Perform this on both valve sides. If you do not clean off this flux, the acid in it will eventually eat via the copper an d make a leak in the pipe.


    Do not forget to unlock the valve before starting to solder. If you do not you will damage the internal seal on a brand new high pressure ball valve. You will have to unsolder it and throw it away.

  • How to install high pressure ball valve

                                                         How to install high pressure ball valve

    High pressure ball valves are the more affordable made gate valves are designed to shut off the water supply to place, such as an irrigation system, or a device, like sink or water heater. Most in-line valves within the home are generally gate valves, but they may rust out faster. So, if you need to replace a defective gate valve, go with the more durable high pressure ball valve. The ball valve consists of a handle on a shaft linked to a metal ball with a space in it. When the handle is turned in the water flow way, the space is covered up, stopping the flow of water via the valve.

    How to install

    Turn off the water supply. Let down towels and a water bucket to grip any drainage from the cut pipe. In both control device replacement works and fresh installations, cut the copper pipe or PVC with a pipe cutter after marking and measuring the space needed to insert the fresh valve with the cut ends firmly into the end sleeves. With a PVC fixing using a high pressure ball control device threaded at both finishes, the space must be broad enough to permit for the valve, 2 short,  one PVC pipes end-threaded screwed into each control device end and 2 perfect socket PVC  links to close the space.

    Perfect all cut finish with emery cloth. Whether the copper links are going to be sweated on which blowtorch and a solder or the PVC pipe is linked with cement, the secret to a water-tight installation is dirt-free pipe finish. Use plumber tape to the threaded pipe if you want to be capable to unscrew it later on. Brush PVC strengthen on all links after twin-checking all measurements. Screw the slice PVC pipes into each end the control device using 2 wrenches to offset the torque  used to the pipe. Protect all perfect socket links.

    Get rid of the heat-responsive, plastic-coated control device actuator handle form the peak of the shaft earlier than outside layer each pipe finish with flux. Install the high force ball valve between the 2 pipes of cut and tightly seat the pipe ends in the control device cup ends. Check the job place for explosives before igniting the blowtorch. Low weight and manage the blue fame to 1-1/2 inches. Place on an even mitt then grasp single end of the control device and perfectly push it toward the end being joined to firmly seat the pipe and before soldering.

    Warm the base of the control device end cup while saving the flame critical away from you. Grip the solder end to the peak of the end cup where the pipe go into the socket until the link is heated enough to begin melting the solder. Without having to shift the solder, it will be anxious into the socket in the region of pipe. Permit it to chill then do the opposite end cup. Turn on the check and water for leaks,check this link to learn more about high pressure ball valve.

  • How to adjust the gas pressure on water heaters

                              How to adjust the gas pressure on water heaters          

    Hot water heaters that depend on gas are fed via series of supply lines and high pressure ball valves that manage the flow of the gas. Almost all warm water heaters self-regulate the amount of force that is launched into the heating element. This means that amount of gas click here force generally cannot be regulated manually. Anyway, the high pressure ball valve that launch gas into the line of supply can become stuck in a open-part, part-closed place, which can decrease the performance of the gas. Making sure the high pressure ball valve is fully unlock will make sure the top possible performance from your warm water heater.

    It is vital to ensure the gas valve is completely open on warm water heater lines.

    Step 1

    Place the high pressure ball valve along the line of gas that feeds into your water warmer. The line of gas is generally yellow colored and the high pressure ball valve will expected to be blue or red.

    Use a flashlight to view in dark places.

    Step 2

    Note the place of the high pressure ball valve. If the control device is turned to be completely "On position, there is nothing more you can perform to adjust the gas force.

    If the control device is not turned all the way, but warm water is being generated, turn the control device all the way to the "On" place.

    Step 3

    If the control device is partially in the "On" position but there is no warm water, turn the valve to the "Off" place and wait 5 minutes. Turn the control device to the "On" place, turn the gas valve on the warm water heater to the "Pilot" place.

    Press down on the "ignition" key until you view the pilot frame within the heater. Turn the gas control device to the "On" or "Run" position.

    Maintaining your water heater

    You probably take your house storage tank water heater for granted, since it does its job silently and is housed out of the way, but annually maintenance can make your water heater last longer and job well. Read the appliance manual, if you have one. If you do not, you may want to get one from the producer or through internet. You may feel more relax scheduling a skilled expert to do it.

    Check the pressure relief control device. This valve shows a little handle at the top of the discharge pipe that is placed vertically on the outside of the tank. If you have an issue locating the pipe and the high pressure ball valve, check the manual. If this part is not working rightly, it can lead to-in the worst- an explosion - case scenario. Though rare, it is very a best reason to get your water heater checked yearly.

    How to check the pressure relief valve:

    • Put a bucket within the pipe and lift the lever
    • Water should appear of the pipe into the bucket.

  • Globe Valves VS stainless steel ball valves

                                         Globe Valves VS stainless steel ball valves

    There are many different kinds of valves for different applications, so how do you know which is the top to use for your applications? We will begin by looking at globe valves and stainless steel ball valves. The main difference between these 2 kinds is the way they close. A globe control device uses a plug that locks against the flow, and a stainless steel ball valve has a gate that shuts across the flow. Globe control devices are best for regulating flow, whereas stainless steel ball valves are better for off/on control without force drop.

    From many years, globe valves were known as the industry quality in control valves. They are made with a stem that goes up and down within the valve to manage flow. They are generally used on chill and warm water coils, and bigger models are often used to manage flow to chillers. One of the best restrictions of globe vales is that their close-off rating can lower than other control devices, especially in the bigger sizes.

    Stainless steel ball valves are designed with a ball within the valve. The ball has a hole through the middle so that when the gap is in line with both ends of the valve, flow will happen. When the control device is closed by rotating the ball ninety-degrees, the gap is perpendicular to the finish of the control device, and so flow is barren. Ball valves are extremely website durable and generally have amazing close off even after long use. They are commonly preferred over globe valves in shutoff applications. The big limitations for stainless steel ball valves is proportional control because of the big amount of flow that the ball permits.

    This is a type of steel that possesses high resistivity to corrosion is called as stainless steel. A protective coating due to the structure of passive oxide film permits the steel to repair itself. A rise in chromium content and the level of molybdenum rises the resistive property of the protective layer. Typically, the quality of alloys of stainless steel that is applicable of piping have 8-12% nickel and 17-18% chromium. Stainless steel ball valves are very reliable, durable, and capable performing well after a number of cycles and closing in a safe manner, even after longer period of discus. These specs of stainless steel ball valves make them an amazing choice for shutoff and control applications.

    Stainless steel ball valve are strong, performing well after many cycles, closing securely even after long period of discus. These features make them an amazing choice for shutoff applications, where they are generally preferred to globe and gates valves. On the flip side, stainless steel ball valves do lack the fine control in throttling applications provided by globe valves. This is a largely famous name across a number of industrial sectors owing specifically to the top standard and durability.



Free Website Created & Hosted by Site Builder

Create Yours 500s of Templates. No coding needed.Get started now Create your website like mine with website builder. Start My Website